×
Troubleshooting OpenShift SDN
Overview
As described in the SDN documentation there are multiple layers of interfaces that are created to correctly pass the traffic from one container to another. In order to debug connectivity issues, you have to test the different layers of the stack to work out where the problem arises. This guide will help you dig down through the layers to identify the problem and how to fix it.
Part of the problem is that OpenShift enterprise can be set up many ways, and the networking can be wrong in a few different places. So this document will work through some scenarios that, hopefully, will cover the majority of cases. If your problem is not covered, the tools and concepts that are introduced should help guide debugging efforts.
Nomenclature
- Cluster
-
The set of machines in the cluster. i.e. the Masters and the Nodes.
- Master
-
A controller of the OpenShift enterprise cluster. Note that the master may not be a node in the cluster, and thus, may not have IP connectivity to the pods.
- Node
-
Host in the cluster running OpenShift enterprise that can host pods.
- Pod
-
Group of containers running on a node, managed by OpenShift enterprise.
- Service
-
Abstraction that presents a unified network interface that is backed by one or more pods.
- Router
-
A web proxy that can map various URLs and paths into OpenShift enterprise services to allow external traffic to travel into the cluster.
- Node Address
-
The IP address of a node. This is assigned and managed by the owner of the network to which the node is attached. Must be reachable from any node in the cluster (master and client).
- Pod Address
-
The IP address of a pod. These are assigned and managed by OpenShift enterprise. By default they are assigned out of the 10.128.0.0/14 network (or, in older versions, 10.1.0.0/16). Only reachable from the client nodes.
- Service Address
-
An IP address that represents the service, and is mapped to a pod address internally. These are assigned and managed by OpenShift enterprise. By default they are assigned out of the 172.30.0.0/16 network. Only reachable from the client nodes.
The following diagram shows all of the pieces involved with external access.
Debugging external Access to an HTTP Service
If you are on an machine outside the cluster and are trying to access a resource provided by the cluster there needs to be a process running in a pod that listens on a public IP address and "routes" that traffic inside the cluster. The OpenShift enterprise router serves that purpose for HTTP, HTTPS (with SNI), WebSockets, or TLS (with SNI).
Assuming you can’t access an HTTP service from the outside of the cluster, let’s start by reproducing the problem on the command line of the machine where things are failing. Try:
curl -kv http://foo.example.com:8000/bar # But replace the argument with your URL
If that works, are you reproducing the bug from the right place? It is also possible that the service has some pods that work, and some that don’t. So jump ahead to the Debugging the Router section.
If that failed, then let’s resolve the DNS name to an IP address (assuming it isn’t already one):
dig +short foo.example.com # But replace the hostname with yours
If that doesn’t give back an IP address, it’s time to troubleshoot DNS, but that’s outside the scope of this guide.
| Make sure that the IP address that you got back is one that you expect to be running the router. If it’s not, fix your DNS. |
Next, use ping -c address and tracepath address to check that
you can reach the router host. It is possible that they will not
respond to ICMP packets, in which case those tests will fail, but the
router machine may be reachable. In which case, try using the telnet
command to access the port for the router directly:
telnet 1.2.3.4 8000
You may get:
Trying 1.2.3.4... Connected to 1.2.3.4. escape character is '^]'.
If so, there’s something listening on the port on the IP address.
That’s good. Hit ctrl-] then hit the enter key and then type
close to quit telnet. Move on to the Debugging the Router
section to check other things on the router.
Or you could get:
Trying 1.2.3.4... telnet: connect to address 1.2.3.4: Connection refused
Which tells us that the router is not listening on that port. Please see the Debugging the Router section for more pointers on how to configure the router.
Or if you see:
Trying 1.2.3.4...
telnet: connect to address 1.2.3.4: Connection timed outWhich tells us that you can’t talk to anything on that IP address. Check your routing, firewalls, and that you have a router listening on that IP address. To debug the router, see the Debugging the Router section. For IP routing and firewall issues, debugging that is beyond the purview of this guide.
Debugging the Router
Now that you have an IP address, we need to ssh to that machine and
check that the router software is running on that machine and
configured correctly. So let’s ssh there and get administrative
OpenShift enterprise credentials.
|
If you have access to administrator credentials but are no longer logged in as the default system user system:admin, you can log back in as this user at any time as long as the credentials are still present in your CLI configuration file. The following command logs in and switches to the default project: $ oc login -u system:admin -n default |
Check that the router is running:
# oc get endpoints --namespace=default --selector=router NAMeSPACe NAMe eNDPOINTS default router 10.128.0.4:80
If that command fails, then your OpenShift enterprise configuration is broken. Fixing that is outside the scope of this document.
You should see one or more router endpoints listed, but that won’t tell you if they are running on the machine with the given external IP address, since the endpoint IP address will be one of the pod addresses that is internal to the cluster. To get the list of router host IP addresses, run:
# oc get pods --all-namespaces --selector=router --template='{{range .items}}HostIP: {{.status.hostIP}} PodIP: {{.status.podIP}}{{end}}{{"\n"}}'
HostIP: 192.168.122.202 PodIP: 10.128.0.4
You should see the host IP that corresponds to your external address. If you do not, please refer to the router documentation to configure the router pod to run on the right node (by setting the affinity correctly) or update your DNS to match the IP addresses where the routers are running.
At this point in the guide, you should be on a node, running your router pod, but you still cannot get the HTTP request to work. First we need to make sure that the router is mapping the external URL to the correct service, and if that works, we need to dig into that service to make sure that all endpoints are reachable.
Let’s list all of the routes that OpenShift enterprise knows about:
# oc get route --all-namespaces NAMe HOST/PORT PATH SeRVICe LABeLS TLS TeRMINATION route-unsecured www.example.com /test service-name
If the host name and path from your URL don’t match anything in the list of returned routes, then you need to add a route. See the router documentation.
If your route is present, then you need to debug access to the endpoints. That’s the same as if you were debugging problems with a service, so please continue on with the next Debugging a Service section.
Debugging a Service
If you can’t communicate with a service from inside the cluster (either because your services can’t communicate directly, or because you are using the router and everything works until you get into the cluster) then you need to work out what endpoints are associated with a service and debug them.
First, let’s get the services:
# oc get services --all-namespaces NAMeSPACe NAMe LABeLS SeLeCTOR IP(S) PORT(S) default docker-registry docker-registry=default docker-registry=default 172.30.243.225 5000/TCP default kubernetes component=apiserver,provider=kubernetes <none> 172.30.0.1 443/TCP default router router=router router=router 172.30.213.8 80/TCP
You should see your service in the list. If not, then you need to define your service.
The IP addresses listed in the service output are the Kubernetes service IP addresses that Kubernetes will map to one of the pods that backs that service. So you should be able to talk to that IP address. But, unfortunately, even if you can, it doesn’t mean all pods are reachable; and if you can’t, it doesn’t mean all pods aren’t reachable. It just tells you the status of the one that kubeproxy hooked you up to.
Let’s test the service anyway. From one of your nodes:
curl -kv http://172.30.243.225:5000/bar # Replace the argument with your service IP address and port
Then, let’s work out what pods are backing our service (replace docker-registry with the name of the broken service):
# oc get endpoints --selector=docker-registry NAMe eNDPOINTS docker-registry 10.128.2.2:5000
From this, we can see that there’s only one endpoint. So, if your service test succeeded, and the router test succeeded, then something really odd is going on. But if there’s more than one endpoint, or the service test failed, try the following for each endpoint. Once you identify what endpoints aren’t working, then proceed to the next section.
First, test each endpoint (change the URL to have the right endpoint IP, port, and path):
curl -kv http://10.128.2.2:5000/bar
If that works, great, try the next one. If it failed, make a note of it and we’ll work out why, in the next section.
If all of them failed, then it is possible that the local node is not working, jump to the Debugging Local Networking section.
If all of them worked, then jump to the Debugging Kubernetes section to work out why the service IP address isn’t working.
Debugging Node to Node Networking
Using our list of non-working endpoints, we need to test connectivity to the node.
-
Make sure that all nodes have the expected IP addresses:
# oc get hostsubnet NAMe HOST HOST IP SUBNeT rh71-os1.example.com rh71-os1.example.com 192.168.122.46 10.1.1.0/24 rh71-os2.example.com rh71-os2.example.com 192.168.122.18 10.1.2.0/24 rh71-os3.example.com rh71-os3.example.com 192.168.122.202 10.1.0.0/24
If you are using DHCP they could have changed. ensure the host names, IP addresses, and subnets match what you expect. If any node details have changed, use
oc edit hostsubnetto correct the entries. -
After ensuring the node addresses and host names are correct, list the endpoint IPs and node IPs:
# oc get pods --selector=docker-registry \ --template='{{range .items}}HostIP: {{.status.hostIP}} PodIP: {{.status.podIP}}{{end}}{{"\n"}}' HostIP: 192.168.122.202 PodIP: 10.128.0.4 -
Find the endpoint IP address you made note of before and look for it in the
PodIPentry, and find the correspondingHostIPaddress. Then test connectivity at the node host level using the address fromHostIP:-
ping -c 3 <IP_address>: No response could mean that an intermediate router is eating the ICMP traffic. -
tracepath <IP_address>: Shows the IP route taken to the target, if ICMP packets are returned by all hops.If both
tracepathandpingfail, then look for connectivity issues with your local or virtual network.
-
-
For local networking, check the following:
-
Check the route the packet takes out of the box to the target address:
# ip route get 192.168.122.202 192.168.122.202 dev ens3 src 192.168.122.46 cacheIn the above example, it will go out the interface named
ens3with the source address of192.168.122.46and go directly to the target. If that is what you expected, useip a show dev ens3to get the interface details and make sure that is the expected interface.An alternate result may be the following:
# ip route get 192.168.122.202 1.2.3.4 via 192.168.122.1 dev ens3 src 192.168.122.46
It will pass through the
viaIP value to route appropriately. ensure that the traffic is routing correctly. Debugging route traffic is beyond the scope of this guide.
-
Other debugging options for node to node networking can be solved with the following:
-
Do you have ethernet link on both ends? Look for
Link detected: yesin the output fromethtool <network_interface>. -
Are your duplex settings, and ethernet speeds right on both ends? Look through the rest of the
ethtool <network_interface>information. -
Are the cables plugged in correctly? To the correct ports?
-
Are the switches configured correctly?
Once you have ascertained that the node to node connectivity is fine, we need to look at the SDN configuration on both ends.
Debugging Local Networking
At this point we should have a list of one or more endpoints that you can’t communicate with, but that have node to node connectivity. For each one, we need to work out what is wrong, but first you need to understand how the SDN sets up the networking on a node for the different pods.
The Interfaces on a Node
These are the interfaces that the OpenShift enterprise SDN creates:
-
br0: The OVS bridge device that containers will be attached to. OpenShift enterprise SDN also configures a set of non-subnet-specific flow rules on this bridge. (Themultitenantplug-in does this immediately; theovssubnetplug-in waits until the SDN master announces the creation of the new node subnet.) -
lbr0: A Linux bridge device, which is configured as Docker’s bridge and given the cluster subnet gateway address (eg, 10.128.x.1/23). -
tun0: An OVS internal port (port 2 onbr0). This also gets assigned the cluster subnet gateway address, and is used for external network access. OpenShift enterprise SDN configuresnetfilterand routing rules to enable access from the cluster subnet to the external network via NAT. -
vlinuxbrandvovsbr: Two Linux peer virtual ethernet interfaces.vlinuxbris added tolbr0, andvovsbris added tobr0(port 3), to provide connectivity for containers created directly with Docker outside of OpenShift enterprise. -
vxlan0: The OVS VXLAN device (port 1 onbr0), which provides access to containers on remote nodes. -
vethX(in the main netns): A Linux virtual ethernet peer ofeth0in the docker netns. It will be attached to the OVS bridge on one of the other ports.
SDN Flows Inside a Node
Depending on what you are trying to access (or be accessed from) the path will vary. There are four different places the SDN connects (inside a node). They are labeled in red on the diagram above.
-
Pod: Traffic is going from one pod to another on the same machine (1 to a different 1)
-
Remote Node (or Pod): Traffic is going from a local pod to a remote node or pod in the same cluster (1 to 2)
-
external Machine: Traffic is going from a local pod outside the cluster (1 to 3)
-
Local Docker: Traffic is going from a local pod to a local container that is not managed by Kubernetes (1 to 4)
Of course the opposite traffic flows are also possible.
Debugging Steps
Is IP Forwarding enabled?
Check that sysctl net.ipv4.ip_forward is set to 1 (and check the host if this is a VM)
Is firewalld Disabled?
Check that firewalld is disabled using systemctl status firewalld.
If it is running, you either need to disable it, or check
that it is not blocking traffic. That is outside the scope of this
guide.
Are your routes correct?
Check the route tables with ip route:
# ip route
default via 192.168.122.1 dev ens3
10.128.0.0/14 dev tun0 proto kernel scope link # This sends all pod traffic into OVS
10.128.2.0/23 dev tun0 proto kernel scope link src 10.128.2.1 # This is traffic going to local pods, overriding the above
169.254.0.0/16 dev ens3 scope link metric 1002 # This is for Zeroconf (may not be present)
172.17.0.0/16 dev docker0 proto kernel scope link src 172.17.42.1 # Docker's private IPs... used only by things directly configured by docker; not {product-title}
192.168.122.0/24 dev ens3 proto kernel scope link src 192.168.122.46 # The physical interface on the local subnet
You should see the 10.128.x.x lines (assuming you have your pod network set to the default range in your configuration). If you do not, check the OpenShift enterprise logs (see the Reading the Logs section)
Is the Open vSwitch configured correctly?
Check the Open vSwitch bridges on both sides:
# ovs-vsctl list-br br0
This should just be br0.
You can list all of the ports that ovs knows about:
# ovs-ofctl -O OpenFlow13 dump-ports-desc br0
OFPST_PORT_DeSC reply (OF1.3) (xid=0x2):
1(vxlan0): addr:9e:f1:7d:4d:19:4f
config: 0
state: 0
speed: 0 Mbps now, 0 Mbps max
2(tun0): addr:6a:ef:90:24:a3:11
config: 0
state: 0
speed: 0 Mbps now, 0 Mbps max
8(vethe19c6ea): addr:1e:79:f3:a0:e8:8c
config: 0
state: 0
current: 10GB-FD COPPeR
speed: 10000 Mbps now, 0 Mbps max
9(vovsbr): addr:6e:dc:28:df:63:c3
config: 0
state: 0
current: 10GB-FD COPPeR
speed: 10000 Mbps now, 0 Mbps max
LOCAL(br0): addr:0a:7f:b4:33:c2:43
config: PORT_DOWN
state: LINK_DOWN
speed: 0 Mbps now, 0 Mbps max
Next list the flows that are configured on that bridge. In output
below I have removed the cookie, duration, n_packets and
n_bytes columns; and I have lined up the various columns to make it
easier to understand, and added in-line comments and blank lines:
# ovs-ofctl -O OpenFlow13 dump-flows br0 OFPST_FLOW reply (OF1.3) (xid=0x2): # external access is the default if no higher priority matches table=0, priority=50 actions=output:2 # ARP and IP Traffic destined for the local subnet gateway goes out of the switch to # IP tables and the main route table table=0, priority=100,arp,arp_tpa=10.128.2.1 actions=output:2 table=0, priority=100, ip, nw_dst=10.128.2.1 actions=output:2 # All remote nodes should have two entries here, one for IP and one for ARP. # Here we see the entries for two remote nodes table=0, priority=100,arp,arp_tpa=10.128.4.0/23 actions=set_field:192.168.122.18->tun_dst,output:1 table=0, priority=100, ip, nw_dst=10.128.4.0/23 actions=set_field:192.168.122.18->tun_dst,output:1 table=0, priority=100,arp,arp_tpa=10.128.0.0/23 actions=set_field:192.168.122.202->tun_dst,output:1 table=0, priority=100, ip, nw_dst=10.128.0.0/23 actions=set_field:192.168.122.202->tun_dst,output:1 # Other traffic destined for a local pod IP that hasn't been handled by a higher priority rule # goes out port 9 to the virtual bridge for docker table=0, priority=75, ip, nw_dst=10.128.2.0/23 actions=output:9 table=0, priority=75, arp,arp_tpa=10.128.2.0/23 actions=output:9 # Then ports 3-8 or 10+ are for local pods, here there are two local pods table=0, priority=100, ip, nw_dst=10.128.2.7 actions=output:8 table=0, priority=100,arp,arp_tpa=10.128.2.7 actions=output:8 table=0, priority=100, ip, nw_dst=10.128.2.10 actions=output:12 table=0, priority=100,arp,arp_tpa=10.128.2.10 actions=output:12
The SDN networking plug-in configures two entries (one for arp and one
for ip) with output=1 per peer endpoint (i.e. if there are five
nodes, then there should be 4 * 2 rules; In the example above we have
3 nodes total, so there are four entries above). It also sets up the
other entries on ports 2 and 9 that are shown above. If there are
flows missing, please look in the Reading the Logs section.
Debugging Virtual Networking
Builds on a Virtual Network are Failing
If you are installing OpenShift enterprise using a virtual network (for example,
OpenStack), and a build is failing, the maximum transmission unit (MTU) of the
target node host might not be compatible with the MTU of the primary network
interface (for example, eth0).
For a build to complete successfully, the MTU of an SDN must be less than the eth0 network MTU in order to pass data to between node hosts.
-
Check the MTU of your network by running the
ip addrcommand:# ip addr --- 2: eth0: <BROADCAST,MULTICAST,UP,LOWeR_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether fa:16:3e:56:4c:11 brd ff:ff:ff:ff:ff:ff inet 172.16.0.0/24 brd 172.16.0.0 scope global dynamic eth0 valid_lft 168sec preferred_lft 168sec inet6 fe80::f816:3eff:fe56:4c11/64 scope link valid_lft forever preferred_lft forever ---The MTU of the above network is 1500.
-
The MTU in your node configuration must be lower than the network value. Check the
mtuin the node configuration of the targeted node host:# cat /etc/origin/node/node-config.yaml ... networkConfig: mtu: 1450 networkPluginName: company/openshift-ovs-subnet ...
In the above node configuration file, the
mtuvalue is lower than the network MTU, so no configuration is needed. If themtuvalue was higher, edit the file and lower the value to at least 50 units fewer than the MTU of the primary network interface, then restart the node service. This would allow larger packets of data to pass between nodes.
Debugging Pod egress
If you are trying to access an external service from a pod, e.g.:
curl -kv github.com
Make sure that the DNS is resolving correctly:
dig +search +noall +answer github.com
That should return the IP address for the github server, but check that you got back the correct address. If you get back no address, or the address of one of your machines, then you may be matching the wildcard entry in your local DNS server.
To fix that, you either need to make sure that DNS server that has the
wildcard entry is not listed as a nameserver in your
/etc/resolv.conf or you need to make sure that the wildcard domain
is not listed in the search list.
If the correct IP address was returned, then try the debugging advice
listed above in Debugging Local Networking. Your traffic should
leave the Open vSwitch on port 2 to pass through the iptables rules, then
out the route table normally.
Reading the Logs
Run: journalctl -u atomic-openshift-node.service --boot | less
Look for the Output of setup script: line. everything starting with
'+' below that are the script steps. Look through that for obvious
errors.
Following the script you should see lines with Output of adding
table=0. Those are the OVS rules, and there should be no errors.
Debugging Kubernetes
Check iptables -t nat -L to make sure that the service is being
NAT’d to the right port on the local machine for the kubeproxy.
This is all changing soon… Kubeproxy is being eliminated and
replaced with an iptables-only solution.
|
Further Help
-
Run the script at https://raw.githubusercontent.com/openshift/openshift-sdn/master/hack/debug.sh on the master (or from another machine with access to the master) to generate useful debugging information.
-
When debugging IP failover problems, run the script at https://raw.githubusercontent.com/openshift/openshift-sdn/master/hack/ipf-debug.sh on the master (or from another machine with access to the master) to generate useful debugging information.
Miscellaneous Notes
Other clarifications on ingress
-
Kube - declare a service as NodePort and it will claim that port on all machines in the cluster (on what interface?) and then route into kube-proxy and then to a backing pod. See http://kubernetes.io/v1.0/docs/user-guide/services.html#type-nodeport (some node must be accessible from outside)
-
Kube - declare as a LoadBalancer and something you have to write does the rest
-
OS/Ae - Both use the router
TLS Handshake Timeout
When a pod fails to deploy, check its docker log for a TLS handshake timeout:
$ docker log <container_id> ... [...] couldn't get deployment [...] TLS handshake timeout ...
This condition, and generally, errors in establishing a secure connection, may be caused by a large difference in the MTU values between tun0 and the primary interface (e.g., eth0), such as when tun0 MTU is 1500 and eth0 MTU is 9000 (jumbo frames).